Fuel Savers and Water Conditioners.
All these have the following in common:-
no power supply - no electricity
use - emit no harmful electromagnetic waves
· help save the
90 day money back guarantee
of satisfied users
for 10 years for faults and workmanship
Pretty amazing.......................!! look in more detail................
Motoflow 1 and 2.
Why buy a Motoflow M1?
Fit the Motoflow M1 fuel
saving device, and without modifying your engine, you can:
Depending upon the condition of your engine and your
driving style, you should notice improvements within 1,000 miles of fitting the
Motoflow M1 fuel saving device to a petrol engine (maybe a little longer for
diesel engines). Remember that better fuel combustion will give you more power,
but your driving style dictates whether this will give you a fuel saving or
fuel consumption - saving you money and
conserving the world's energy reserves;
- Help minimise
pollution by lowering exhaust emissions (carbon monoxide, created when
you burn fuel, and hydrocarbons, which are unburnt fuel);
power/torque - so your vehicle is more
responsive (able to pull heavier loads or accelerate more quickly);
the life of your catalytic converters, exhaust systems and spark plugs by
minimising carbon deposits.
Motoflow was designed to condition the fuel prior to
combustion. In a similar way that water conditioned by heat (hot water) carries
more energy and mixes with other substances more readily than cold water, fuel
conditioned by a strong magnetic field carries more energy and mixes more
readily with air resulting in a more complete combustion i.e. more energy and
less waste from the same amount of fuel. The process of conditioning fuel
through the introduction of a specific magnetic field is known as lonisation by
Magnetic Induction (IMI).
Motoflow is manufactured in Neodymium 32, with a axially
polarised Central Reverse Polarity modules contained in a Hytel shell.
Motoflow is suitable for all petrol & diesel engines, including
fuel-injected systems and carburettor engines. Secured to the fuel line
bringing fuel to the engine, no pipe cutting or modification to manufactured
parts is required.
Engines up to 3 litres - 1 x Motoflow M2
Engines over 3 litres - 2 x Motoflow M2
Motorcycles - 1 x Motoflow M2
Weight: 36 grams. Size: 35 x 28 x 13 mm
..................................fit after the fuel filter and before the injectors/carborettor.
ALL modern vehicles must be
fitted with Motoflow following the full HOT FIT routine in order to ensure the
Motoflow works correctly. Otherwise the result could be NO fuel saving, rough
running and even lower mpg ! Yes, it’s true that carburettor cars and older
diesel engines can be fitted cold, and a few modern vehicles can too-but which
In my view this is too risky. For the majority of
electronic fuel injected petrol and diesel vehicles, failure to HOT FIT will
cause the engine management system to compensate for the lower emissions
the Ecoflow produces. This means a richer fuel mixture will be injected into
the engine, leading to higher consumption, worse emissions and poor
performance….Not what you want, right ? So what does HOT FIT really mean and
how does it differ from other installation methods? Here’s my default fitting
instructions for Motoflow……
First identify the fuel feed near to the engine
and mark it with a piece of tape. Drive the vehicle for 20 miles or more
to ensure the engine and exhaust system are all up to working temperature. Keep
the engine running, if possible and fit Motoflow onto the fuel feed pipe, taking care to keep hands and
clothing away from hot and moving parts.
Leave the engine running at
tickover for a further 20 minutes. Finally, raise the revs to 1500 rpm
for 2 minutes and the job is completed !
unit is designed for use on oil and gas
heating appliances, including LPG, to reduce fuel costs.
Appliances that are
fitted with Thermoflow also benefit from lower soot levels which reduce
Thermoflow conditions the fuel to burn more quickly and more efficiently, this
ensures the maximum amount of fuel is burned within the length of the flame.
Using a Thermoflow provides more heat from a given amount of fuel allowing the
energy requirements of the appliance boiler, heater, oven etc to be reduced.
It is manufactured in rare earth Strontium Ceramic, poled
tri-axially, contained in ABS shell.
Simple DIY installation......we will help if you want
us to........if you live locally
No pipes to cut
No moving parts.
No power supply.
Zero running costs and requires no maintenance.
Fit and forget it, but when you move , do take it
with you !
Can improve combustion efficiency
Can reduce emissions
Suitable for Gas, Oil and Propane boilers and
Guaranteed – 90 day, 100% money back
performance guarantee and 10 year
A single Thermoflow unit is suitable for boilers up
to 80,000btu / 25KW. That size boiler is usually adequate for a 3 to 4 bedroom
property. Larger boilers will require two or more units….or an
Over the last 17 years, this unit has proved highly
effective in thousands of homes, offices and factories around the UK, so I am
confident you could see good results too……. Ours, on a 5year old combi boiler,
saves us at least 12% when running all the time in the winter months